A graphics card that runs hotter and louder than it did when new usually has a simple cause: the factory paste between the GPU die and the cold plate has dried out or pumped out after thousands of heat cycles. Repasting restores that interface, and the compound chosen decides how long the fix lasts. A GPU die is bare silicon with no heat spreader, mounting pressure is lower than on a CPU cooler, and the swing between idle and full load squeezes thin pastes toward the edges. That is why this roundup favors thick, electrically non-conductive compounds with published specification sheets.

Our top pick: Thermal Grizzly Kryonaut 1g. Runner-up: GELID Solutions GC-Extreme 3.5g.

The five pastes below cover the main buying angles: a premium compound, two viscous mid-range staples with long track records on bare dies, a long-service-life paste for cards that stay sealed for years, and a budget syringe with a strong spec sheet. Every pick is electrically non-conductive, which matters where the die sits surrounded by tiny surface-mount components.

As an Amazon Associate, we earn from qualifying purchases.

Quick Answer

For most graphics cards, the Thermal Grizzly Kryonaut is the best thermal paste for a repaste: it publishes 12.5 W/mK conductivity and is electrically non-conductive, which matters on a bare die. The GELID GC-Extreme and ARCTIC MX-6 are thicker mid-range alternatives, the Noctua NT-H2 suits long service intervals, and the Thermalright TF7 is the budget pick.

Table of Contents

  • Thermal Grizzly Kryonaut 1g — Best Premium
  • GELID Solutions GC-Extreme 3.5g — Best for Bare Dies
  • ARCTIC MX-6 (4 g) — Best All-Rounder
  • Noctua NT-H2 3.5g — Best for Long Service Intervals
  • Thermalright TF7 (8 g) — Best Budget
  • How to Choose
  • Who Should Skip
  • FAQ
  • Conclusion

Thermal Grizzly Kryonaut 1g — Best Premium

Kryonaut is Thermal Grizzly’s compound for demanding applications, carrying the highest published conductivity figure in this roundup: 12.5 W/mK, with a stated thermal resistance of 0.0032 K/W. The formula uses aluminum and zinc oxide nanoparticles that Thermal Grizzly says prevent drying out at temperatures up to 80 °C, and its operating range runs from -250 °C to +350 °C. Despite the metal content, Thermal Grizzly lists the electrical conductivity at 0 pS/m, so the paste is non-conductive and safe around the components next to a GPU die.

Application is where Kryonaut asks for care. Its viscosity of 130 to 170 Pa·s makes it thinner than the ARCTIC and GELID pastes here, so the included spatula is the intended method: spread a thin, even layer across the whole die, because a rectangular bare die needs edge-to-edge coverage. The 1 g syringe covers only a few applications.

Specs

    • Quantity: 1 g syringe
    • Thermal conductivity: 12.5 W/mK (manufacturer published)
    • Thermal resistance: 0.0032 K/W
    • Viscosity: 130 to 170 Pa·s
    • Temperature range: -250 °C to +350 °C
    • Electrical conductivity: 0 pS/m (non-conductive)
    • Applicator: spatula included

    GELID Solutions GC-Extreme 3.5g — Best for Bare Dies

    GC-Extreme has been a fixture of enthusiast repaste guides for years, and its published specifications explain the staying power. GELID rates thermal conductivity at 8.5 W/mK with a density of 3.73 g/cm3, and the compound is non-electrically conductive, non-corrosive, non-curing and non-toxic, checking every safety box for a bare die. The operating range of -45 to +180 °C covers anything a graphics card produces.

    The consistency is the practical highlight. GC-Extreme spreads into a thin, even film without running, exactly the behavior wanted on a small rectangular GPU die, and because it does not cure, it reaches full performance as soon as the cooler is remounted. It sits in the mid-range tier: the published conductivity is lower than Kryonaut’s, but the thicker body and long track record make it the default recommendation for a first repaste.

    Specs

      • Quantity: 3.5 g syringe
      • Thermal conductivity: 8.5 W/mK (manufacturer published)
      • Density: 3.73 g/cm3
      • Temperature range: -45 °C to +180 °C
      • Electrical properties: non-conductive, non-corrosive, non-toxic
      • Curing: none required
      • Applicator: tool included

      ARCTIC MX-6 (4 g) — Best All-Rounder

      The MX-6 is ARCTIC’s flagship compound and the paste whose published profile most directly targets the pump-out problem. Its carbon filler formula is rated by ARCTIC as lower in thermal resistance than the earlier MX-4, and it reaches full performance immediately, with no burn-in period. ARCTIC does not publish a W/mK figure for the MX-6, so its case rests on the rest of the data: a viscosity of 45,000 poise makes it thick enough to resist being squeezed off a bare die over repeated heat cycles.

      ARCTIC also publishes a volume resistivity of 1.8 x 10^12 Ω-cm and a breakdown voltage of 7.5 kV/mm, confirming the compound is neither conductive nor capacitive. Because of the high viscosity, it is applied as a dot or line and spread by mounting pressure; on a GPU die, use a slightly larger dot than on a CPU heat spreader so pressure reaches the corners. The 4 g syringe covers several repastes, in the mid-range tier.

      Specs

        • Quantity: 4 g syringe
        • Thermal conductivity: not published by ARCTIC
        • Viscosity: 45,000 poise
        • Continuous use temperature: -50 to 150 °C
        • Electrical conductivity: non-conductive and non-capacitive
        • Volume resistivity: 1.8 x 10^12 Ω-cm
        • Breakdown voltage: 7.5 kV/mm

        Noctua NT-H2 3.5g — Best for Long Service Intervals

        The NT-H2 is the second generation of Noctua’s compound, reformulated with a new blend of metal-oxide microparticles for lower thermal impedance than the earlier NT-H1. Noctua does not publish a W/mK rating, so the case for the NT-H2 rests on handling and longevity: no curing time, no mandatory spreading, and stated figures of at least three years of shelf storage and five years or more of use once applied. For a card that stays sealed for years, that service interval is the reason to pick it.

        The practical upgrade inside the box is three included NA-CW1 cleaning wipes, pre-moistened with an isopropyl alcohol mixture, which turns removing the old factory paste into a one-step job. The NT-H2 is electrically non-conductive, and the 3.5 g syringe covers roughly 3 to 20 applications. It sits in the mid-range tier.

        Specs

          • Quantity: 3.5 g syringe (1.2 ml); 10 g version available
          • Applications: roughly 3 to 20 per syringe
          • Thermal conductivity: not published by Noctua
          • Electrical conductivity: non-conductive
          • Included: 3 NA-CW1 cleaning wipes
          • Storage life: at least 3 years
          • In-use life: 5 years or more, per Noctua

          Thermalright TF7 (8 g) — Best Budget

          TF7 is the budget-tier pick that still brings a serious specification sheet. Thermalright publishes a thermal conductivity of 12.8 W/mK, the highest manufacturer rating in this roundup, and a specific gravity of 2.8 that gives the paste a firm, spreadable body well suited to covering a GPU die without running toward the edges. The compound is electrically non-conductive and non-corrosive, and Thermalright markets it for processors, graphics cards and laptops alike.

          The 8 g syringe listed here is the generous size, with 2 g and 4 g versions for a single job, and a scraper tool is included for the manual spread method. Thermalright rates the paste for long durability, and its firm consistency is why it appears in so many repaste discussions: a paste that stays where it is spread keeps working after thousands of heat cycles.

          Specs

            • Quantity: 8 g syringe (2 g and 4 g versions available)
            • Thermal conductivity: 12.8 W/mK (manufacturer published)
            • Specific gravity: 2.8
            • Electrical properties: non-conductive and non-corrosive
            • Rated use: CPUs, graphics cards and laptops
            • Applicator: scraper tool included

            How to Choose a Thermal Paste for Your GPU

            Start with viscosity, because on a graphics card it matters more than the headline number. The die is bare, mounting pressure is modest, and every heat cycle tries to pump the compound out from under the cold plate. Thick pastes such as the MX-6 and GC-Extreme resist that migration; thinner compounds need a careful manual spread.

            Read conductivity figures with caution. W/mK ratings come from each manufacturer’s own test method, so the numbers are not directly comparable across brands, and two makers here, ARCTIC and Noctua, publish no W/mK figure at all. A missing rating is not a sign of a weak paste; weigh thermal resistance and service life alongside it.

            Confirm electrical safety. Every paste here is non-conductive, the right default around the exposed components next to a GPU die. Liquid metal is a separate category: electrically conductive, able to damage a card if it escapes, and reactive with aluminum, so it does not belong in a general repaste roundup.

            Plan the whole job, not just the paste. Opening the card can give some manufacturers grounds to dispute a warranty claim, so check the warranty position first. Memory and VRM cooling uses thermal pads rather than paste; note their thickness before disassembly, because torn pads need like-for-like replacements. Match quantity to the job too: a 1 g syringe covers a single repaste, while 4 g and 8 g syringes suit anyone maintaining several cards.

            Who Should Skip a GPU Repaste

            A repaste is not always the right move. If a card is still under warranty and running at the temperatures it showed when new, opening it risks the warranty for no gain. Owners of new cards with high but factory-normal hotspot readings should also skip it: a wide gap between average and hotspot temperature on a current-generation card is often a cooler design trait, not failed paste. Anyone whose noise problem comes from case airflow will see little change from new paste, and anyone uncomfortable handling a bare die is better served by a repair shop.

            FAQ

            Does repasting a GPU void the warranty?

            It depends on the brand and the region. Some manufacturers allow cooler removal and judge claims on whether the card was damaged, while others fit warranty stickers to cooler screws and treat a broken seal as grounds for refusal. Check the maker’s stated policy for your region before opening the card, and keep the original screws and pads for refitting.

            How much paste does a GPU die need?

            Enough to cover the whole die in a thin, even film. A GPU die is bare silicon, so unlike a CPU heat spreader it cannot rely on a center dot spreading to every corner under pressure. The common methods are a spatula-spread film, supported by the tools included with the GELID, Thermal Grizzly and Thermalright picks, or a small cross pattern for pressure-spread pastes such as the MX-6.

            Can thermal paste replace thermal pads on a graphics card?

            No. Paste and pads solve different gaps. Paste fills the microscopic interface between the GPU die and the cold plate. Memory chips and VRM components sit further from the cooler and need pads of a specific thickness, commonly 0.5 mm to 2 mm. Substituting paste for a pad leaves those parts effectively uncooled, so replace pads like for like.

            How often should a graphics card be repasted?

            Only when the evidence points to the paste: temperatures and fan speeds climbing under the same workload compared with the card’s earlier behavior, or a widening hotspot delta that cleaning and airflow checks do not explain. The compounds here carry stated in-use lives measured in years, so a healthy card does not need repasting on a schedule.

            Conclusion

            For most repaste jobs, the Thermal Grizzly Kryonaut is the premium answer, pairing a published 12.5 W/mK rating with full electrical safety data. The GELID GC-Extreme and ARCTIC MX-6 are the viscous mid-range staples, one spread by tool and one by mounting pressure. The Noctua NT-H2 trades a conductivity figure for the longest stated service life, while the Thermalright TF7 delivers the strongest published numbers in the budget tier. Whichever compound is chosen, full die coverage and correct pad replacement matter as much as the paste itself.

            Product and ASIN Reference

            Product ASIN
            Thermal Grizzly Kryonaut 1g B011F7W3LU
            GELID Solutions GC-Extreme 3.5g B002P5W4RU
            ARCTIC MX-6 (4 g) B09VDL3CW6
            Noctua NT-H2 3.5g B07MZ45X9G
            Thermalright TF7 (8 g) B0DNQ936MF

            Related guides

            Browse all Cooling guides →

            More from Amazon

            Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

            Amazon Business

            A free business account with business pricing and bulk-buying tools for work, shop or home office.

            Create a business account
            Amazon Prime

            Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

            Start a Prime free trial
            Audible

            Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

            Try Audible free
            Amazon Music Unlimited

            Ad-free music streaming. Eligible new subscribers can start with a free trial.

            Try Music Unlimited free

            As an Amazon Associate we earn from qualifying purchases.